TC500/500A/510/514 dataSheet

admin

  Precision Analog Front Ends with Dual Slope ADC


The TC500/500A/510/514 family are precision analog front ends that implement dual slope A/D converters having a maximum resolution of 17 bits plus sign.As a minimum, each device contains the integrator,zero crossing comparator and processor interface logic.The TC500 is the base (16 bit max)device and requires both positive and negative power supplies.The TC500A is identical to the TC500, except it has improved linearity allowing it to operate to a maximum resolution of 17 bits.The TC510 adds an onboard negative power supply converter for single supply operation.The TC514 adds both a negative power supply converter and a 4 input differential analog multiplexer. Each device has the same processor control interface consisting of 3 wires:control inputs A and B and zero-crossing comparator output (CMPTR).The processor manipulates A,B to sequence the TC5xx through four phases of conversion:Auto Zero,Integrate,Deintegrate and Integrator Zero.During the Auto Zero phase,offset voltages in the TC5xx are corrected by a closed-loop feedback mechanism.The input voltage is applied to the integrator during the Integrate phase.This causes an integrator output dv/dt directly proportional to the magnitude of the input voltage. The higher the input voltage,the greater the magnitude of the voltage stored on the integrator during this phase. At the start of the Deintegrate phase,an external voltage reference is applied to the integrator,and at the same time,the external host processor starts its on-board timer.The processor maintains this state until a transition occurs on the CMPTR output,at which time the processor halts its timer. The resulting timer count is the converted analog data.Integrator Zero (the final phase of conversion)removes any residue remaining in the integrator in preparation for the next conversion. The TC500/500A/510/514 offer high resolution (up to 17 bits)superior 50Hz/60Hz noise rejection,low power operation, minimum I/O connections, low input bias currents and lower cost compared to other converter technologies having similar conversion speeds.

Parameter Name  Value
Input Voltage Range (V)  Vss +1.5V to Vdd -1.5V
Sampling Rate  4 to 10
Programmable resolution/conversion time  Yes
Input Range  Yes
Input Channels  1
Charge pump (-V) output pin  No
Resolution  Up to 16 bits
Sampling Rate (Conv/sec)  4 to 10
Interface  3-wire
Supply Voltage Min (V)  ±4.5
Supply Voltage Max (V)  ±7.5

     Features
Precision (up to 17 Bits)
A/D Converter "Front End"
3-Pin Control Interface to Microprocessor
Flexible: User Can Trade-Off Conversion Speed for Resolution
Single Supply Operation (TC510/514)
4 Input, Differential Analog MUX (TC514)
Automatic Input Voltage Polarity Detection
Low Power Dissipation .... TC500/500A: 10mW TC510/514: 18mW
Wide Analog Input Range ............................ ±4.2V (TC500A/510)
Directly Accepts Bipolar and Differential Input Signals


推荐MICROCHIP全系列产品推广商：（可申请部分免费样片，资料，大家赶快行动吧！）
授权A级代理商;提供技术支持;提供成熟方案;提供免费样品;提供详细资料！
深圳市英锐恩科技有限公司
联系电话: 0755-88845951 82543411传真：0755-82543511
E-mail: enroo@enroo.com
网址: www.enroo.com （”o”为字母）
公司地址: 福田区深南中路嘉汇新城汇商中心1203-1205
专业为客户提供芯片选型指导、技术咨询、开发工具技术支持、产品开发设计等专业的技术服务。
同时为Microchip全系列芯片代理推广商,分销服务商,专业提供Microchip全系列开发工具及技术支持。