TC4404/05 Data Sheet

admin

  TC4404/05 Data Sheet


The TC4404 and TC4405 are CMOS buffer-drivers constructed with complementary MOS outputs, where the drains of the totem-pole output have been left separated so that individual connections can be made to the pull-up and pull-down sections of the output. This allows the insertion of drain-current-limiting resistors in the pull-up and/or pull-down sections, allowing the user to define the rates of rise and fall for a capacitive load; or a reduced output swing, if driving a resistive load, or to limit base current, when driving a bipolar transistor. Minimum rise and fall times, with no resistors, will be less than 30nsec for a 1000pF load. There is no upper limit. For driving MOSFETs in motor-control applications, where slow-ON/fast-OFF operation is desired, these devices are superior to the previously-used technique of adding a diode-resistor combination between the driver output and the MOSFET, because they allow accurate control of turn-ON, while maintaining fast turn-OFF and maximum noise immunity for an OFF device. When used to drive bipolar transistors, these drivers maintain the high speeds common to other Microchip drivers. They allow insertion of a base current-limiting resistor, while providing a separate half-output for fast turn-OFF. By proper positioning of the resistor, either npn or pnp transistors can be driven. For driving many loads in low-power regimes, these drivers, because they eliminate shoot-through currents in the output stage, require significantly less power at higher frequencies, and can be helpful in meeting low-power budgets. Because neither drain in an output is dependent on the other, these devices can also be used as open-drain buffer/drivers where both drains are available in one device, thus minimizing chip count. Unused open drains should be returned to the supply rail that their device sources are connected to (pull-downs to ground, pull-ups to VDD), to prevent static damage. In addition, in situations where timing resistors or other means of limiting crossover currents are used, like drains may be paralleled for greater current carrying capacity. These devices are built to operate in the most demanding electrical environments. They will not latch up under any conditions within their power and voltage ratings; they are not subject to damage when up to 5V of noise spiking of either polarity occurs on their ground pin; and they can accept, without damage or logic upset, up to 1/2 amp of reverse current (of either polarity) being forced back into their outputs. All terminals are fully protected against up to 2 kV of electrostatic discharge.
Parameter Name  Value
Power  Dual  
Peak Output Current (mA)  1500
Output Resistance (RH/RL)(Max. @ 25°C)  10/10
Max. Supply Voltage (V)  18
Input/Output Delay (td1, td2)1 (ns)  30/50
Configuration  Inverting  
Description  Low-Side MOSFET Drivers, 1.5A Peak Output Current
Operating Temp. Range (°C)  -40 to 85

     Features
Independently-Programmable Rise and Fall Times
Low Output Impedance: 7 Ω Typ.
High Speed tR, tF: <30nsec with 1000pF Load
Short Delay Times: < 30nsec
Wide Operating Range: 4.5V to 18V
Latch-Up Protected: Will Withstand > 500mA
Reverse Current (Either Polarity)
Input Withstands Negative Swings Up to – 5V

推荐MICROCHIP全系列产品推广商：（可申请部分免费样片，资料，大家赶快行动吧！）
授权A级代理商;提供技术支持;提供成熟方案;提供免费样品;提供详细资料！
深圳市英锐恩科技有限公司
联系电话: 0755-88845951 82543411传真：0755-82543511
E-mail: enroo@enroo.com
网址: www.enroo.com （”o”为字母）
公司地址: 福田区深南中路嘉汇新城汇商中心1203-1205
专业为客户提供芯片选型指导、技术咨询、开发工具技术支持、产品开发设计等专业的技术服务。
同时为Microchip全系列芯片代理推广商,分销服务商,专业提供Microchip全系列开发工具及技术支持。